/*==============================================================
 File........Alaonix smart 256x160 LCD display module
             Geometry function Test code for Arduino
 Purpose.....This test code for Alaonix smart 256x160 LCD display module
 Board.......Arduino nano
 Software....Arduino 1.8.13
 MCU.........Arduino ATmage328p
 Auther......Alaonix Team
 Website.....WWW.Alaonix.com
 Email.......AlaTeam@Alaonix.com
 Started.....
 Updated.....
 Note: MINIMUM CONNECTION:
       5V  <==========> Ala LCD 5V 
       GND <==========> Ala LCD GND
       Arduino Tx <===> Ala LCD Rx 
=================== Parameter =============================*/
void setup() {
  Serial.begin(19200);        // start serial port at 19200 bps
  delay(1000);
  while (!Serial) {
  // wait for serial port to connect. Needed for native USB port only
  }
}
void loop() {
     Serial.println("ac,0,0");                      // clean buffer
     
     delay(50);
     Serial.println("GA,0,0,255,159,1,0");          // Draw a line
     
     delay(1000);
     Serial.println("GA,0,159,255,0,1,0");          // Draw a line
     
     delay(1000);
     Serial.println("GH,90,120,40,20,1,1,0");       // Draw an ellipse
     
     delay(1000);
     Serial.println("GH,128,80,80,60,0,1,0");       // draw a filled ellipse
     
     delay(1000);
     Serial.println("GB,10,250,20,3,1,0");          // Draw a horizontal line
     
     delay(1000);
     Serial.println("GC,100,5,155,2,1,0");          // Draw a vertical line
     
     delay(1000);
     Serial.println("GD,10,250,40,2,15,5,1,0");     // Draw a horizontal dash line
     
     delay(1000);
     Serial.println("GV,120,5,155,2,12,5,1,0");     // Draw a vertical dash line
     
     delay(1000);
     Serial.println("GF,25,30,100,100,0,1,0");      // Draw a rectangle 
     
     delay(1000);
     Serial.println("GF,15,50,70,90,1,1,0");        // Draw a filled rectangle 
     
     delay(1000);
     Serial.println("GG,120,90,50,0,1,0");          // Draw a square
     
     delay(1000);
     Serial.println("GG,130,100,50,1,1,0");         // Draw a filled square
     
     delay(1000);
     Serial.println("GI,200,70,40,0,1,0");          // Draw a circle
     
     delay(1000);
     Serial.println("GI,210,80,30,1,1,0");          // Draw a filled circle
     
     delay(1000);
     Serial.println("GJ,140,60,35,0,90,0,0,1,0");   // Draw a rotatable triangle
     
     delay(1000);
     Serial.println("GJ,120,50,35,0,180,0,1,1,0");  // Draw a filled rotatable triangle
     
     delay(1000);
     Serial.println("ac,0,0");                      // clean buffer
     
     delay(50);
     Serial.println("fa,12,35,30,2,1,0,Thank you for watch!");  // Write text
     
     delay(50);
     Serial.println("Gb,20,236,62,2,1,0");          // Draw a line
     
     delay(150);
     Serial.println("fA,25,25,65,0,1,0,Alaonix");   // Write text 
     
     delay(1000);
     exit(0);
}